Bananian
How to boot Banana Pro from SD card?
2
2380
View: 2380|Reply: 2
|
[Bananian]
How to boot Banana Pro from SD card?
[Copy link]
|
|
Edited by Tido at Apr 10, 2016 21:43
I formated via Windows using SD-Formatter and ImageWriter
I get this on the console when booting. NOTE: I have used 2 different Kingston 8 GB Micro SD cards.
- U-Boot SPL 2015.10-rc1-00655-g632093b (Aug 16 2015 - 17:26:33)
- DRAM: 1024 MiB
- CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
- U-Boot 2015.10-rc1-00655-g632093b (Aug 16 2015 - 17:26:33 +0000) Allwinner Technology
- CPU: Allwinner A20 (SUN7I)
- I2C: ready
- DRAM: 1 GiB
- MMC: SUNXI SD/MMC: 0
- *** Warning - bad CRC, using default environment
- Setting up a 720x576i composite-pal console (overscan 32x20)
- In: serial
- Out: vga
- Err: vga
- SCSI: SUNXI SCSI INIT
- SATA link 0 timeout.
- AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
- flags: ncq stag pm led clo only pmp pio slum part ccc apst
- Net: eth0: ethernet@01c50000
- starting USB...
- USB0: USB EHCI 1.00
- USB1: USB OHCI 1.0
- USB2: USB EHCI 1.00
- USB3: USB OHCI 1.0
- scanning bus 0 for devices... 1 USB Device(s) found
- scanning bus 2 for devices... 1 USB Device(s) found
- scanning bus 1 for devices... 2 USB Device(s) found
- scanning bus 3 for devices... 2 USB Device(s) found
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- Scanning mmc 0:1...
- Found U-Boot script /boot.scr
- reading /boot.scr
- 1676 bytes read in 33 ms (48.8 KiB/s)
- ## Executing script at 43100000
- reading uImage-next
- ** Unable to read file uImage-next **
- reading script.bin
- 50936 bytes read in 232 ms (213.9 KiB/s)
- reading uImage
- Error reading cluster
- ** Unable to read file uImage **
- ## Booting kernel from Legacy Image at 48000000 ...
- Image Name: Linux-3.4.108-bananian
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 4779584 Bytes = 4.6 MiB
- Load Address: 40008000
- Entry Point: 40008000
- Verifying Checksum ... Bad Data CRC
- ERROR: can't get kernel image!
- SCRIPT FAILED: continuing...
- ** Can't read partition table on 0:0 **
- ** Invalid partition 1 **
- ** Can't read partition table on 0:0 **
- ** Invalid partition 1 **
- ** Can't read partition table on 0:0 **
- ** Invalid partition 1 **
- scanning bus for devices...
- Found 0 device(s).
- SCSI device 0:
- Device 0: not available
- USB device 0: unknown device
- ethernet@01c50000 Waiting for PHY auto negotiation to complete.... done
- Speed: 100, full duplex
- BOOTP broadcast 1
- BOOTP broadcast 2
- DHCP client bound to address 10.200.200.124 (2529 ms)
- *** Warning: no boot file name; using '0AC8C87C.img'
- Using ethernet@01c50000 device
- TFTP from server 0.0.0.0; our IP address is 10.200.200.124; sending through gateway 10.200.200.1
- Filename '0AC8C87C.img'.
- Load address: 0x42000000
- Loading: *
- TFTP error: 'illegal (unrecognized) tftp operation' (4)
- Starting again
- missing environment variable: pxeuuid
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/01-02-8c-06-41-7b-1a
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/0AC8C87C
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/0AC8C87
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/0AC8C8
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/0AC8C
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/0AC8
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/0AC
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/0A
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/0
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/default-arm-sunxi
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/default-arm
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- missing environment variable: bootfile
- Retrieving file: pxelinux.cfg/default
- Speed: 100, full duplex
- *** ERROR: `serverip' not set
- Config file not found
- Speed: 100, full duplex
- BOOTP broadcast 1
- BOOTP broadcast 2
- DHCP client bound to address 10.200.200.124 (717 ms)
- Using ethernet@01c50000 device
- TFTP from server 0.0.0.0; our IP address is 10.200.200.124; sending through gateway 10.200.200.1
- Filename 'boot.scr.uimg'.
- Load address: 0x43100000
- Loading: *
- TFTP error: 'illegal (unrecognized) tftp operation' (4)
- Starting again
Copy the Code
=>
|
|
|
|
|
|
|
|
Edited by Tido at Apr 10, 2016 21:46
Hi,
Remove all parts that need power, like harddisk.
Have you tried with a different PowerSupply?
Have you tried with a different cable?
|
|
|
|
|
|
|
|
I have not tried that. I used the power supply that came with the all-in-one ket that I purchased off of Amazon. |
|
|
|
|
|
|