Bananian

Won't boot after update to 14.09

31 6354
Reply 10# Cubytus


    Have you tried Raspbian or any other image? Is it working for you?

Cubytus  
Raspbian is working well. On the previous version of Bananian, the bs=1M parameter prevented boot altogether. Now with the same parameter, boot starts, but stops after kernel panic.

Cubytus  
I got a booting 14.09 version of Bananian. Instead of the line
  1. dd if=bananian-1409.img of=/dev/<your-sd-card> bs=1M && sync
Copy the Code
One has to use
  1. dd if=bananian-1409.img of=/dev/<your-sd-card> bs=4M && sync
Copy the Code
I don't know why 1M fails, but I do know it took 3 hours and a half to write, while the 4M took 15 minutes only. Both were done on 8GB Class 4 microSD cards.

I can boot the 14.09 Bananian normally. And I also use bs=4M

koev  
Same with my banana pi. Tried several sd cards, checked the sha1sum. 14.08 works fine. After an update I got the same weird behavior.

Not booting. Nothing on the screen
LED red: is on
LED green: slowly blinks

suppser  
Post Last Edited by suppser at 2014-10-10 15:07

Hello,

I have the same problem, I can boot 14.08 without problems, but after update it's over, with a fresh 14.09 image to sd card, I have the same problem.
(I Used dd with -bs 4M and the gnome-disk-utility 3.12.1)

It see to be a bootloop

here are some output from serial port J11

  1. U-Boot SPL 2014.04-10694-g2ae8b32 (Sep 03 2014 - 20:53:14)
  2. Board: Bananapi
  3. DRAM: 1024 MiB
  4. CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
  5. spl: not an uImage at 1600


  6. U-Boot 2014.04-10694-g2ae8b32 (Sep 03 2014 - 20:53:14) Allwinner Technology

  7. CPU:   Allwinner A20 (SUN7I)
  8. Board: Bananapi
  9. I2C:   ready
  10. DRAM:  1 GiB
  11. MMC:   SUNXI SD/MMC: 0
  12. *** Warning - bad CRC, using default environment

  13. In:    serial
  14. Out:   serial
  15. Err:   serial
  16. Net:   dwmac.1c50000
  17. Hit any key to stop autoboot:  0
  18. reading uEnv.txt
  19. 378 bytes read in 16 ms (22.5 KiB/s)
  20. Loaded environment from uEnv.txt
  21. Running uenvcmd ...
  22. reading script.bin
  23. 50908 bytes read in 30 ms (1.6 MiB/s)
  24. reading uImage
  25. 4790856 bytes read in 243 ms (18.8 MiB/s)
  26. ## Booting kernel from Legacy Image at 48000000 ...
  27.    Image Name:   Linux-3.4.90+
  28.    Image Type:   ARM Linux Kernel Image (uncompressed)
  29.    Data Size:    4790792 Bytes = 4.6 MiB
  30.    Load Address: 40008000
  31.    Entry Point:  40008000
  32.    Verifying Checksum ... OK
  33.    Loading Kernel Image ... OK

  34. Starting kernel ...

  35. <6>Booting Linux on physical CPU 0
  36. <6>Initializing cgroup subsys cpuset
  37. <6>Initializing cgroup subsys cpu
  38. <5>Linux version 3.4.90+ (root@nico-desktop) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #1 SMP PREEMPT Fri Sep 12 18:13:45 CEST 2014
  39. CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
  40. CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  41. Machine: sun7i
  42. <6>Memory Reserved:
  43. <6>     SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
  44. <6>     LCD  : 0x44000000 - 0x45ffffff  (  32 MB)
  45. Memory policy: ECC disabled, Data cache writealloc
  46. <6>sunxi: Allwinner A20 (AW1651/sun7i) detected.
  47. <7>On node 0 totalpages: 262144
  48. <7>free_area_init_node: node 0, pgdat c09089c0, node_mem_map d0000000
  49. <7>  DMA zone: 512 pages used for memmap
  50. <7>  DMA zone: 0 pages reserved
  51. <7>  DMA zone: 65024 pages, LIFO batch:15
  52. <7>  Normal zone: 1008 pages used for memmap
  53. <7>  Normal zone: 128016 pages, LIFO batch:31
  54. <7>  HighMem zone: 528 pages used for memmap
  55. <7>  HighMem zone: 67056 pages, LIFO batch:15
  56. <6>PERCPU: Embedded 7 pages/cpu @d0808000 s7616 r8192 d12864 u32768
  57. <7>pcpu-alloc: s7616 r8192 d12864 u32768 alloc=8*4096<c>
  58. <7>pcpu-alloc: <c>[0] <c>0 <c>[0] <c>1 <c>
  59. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
  60. <5>Kernel command line: console=ttyS0,115200 console=tty0 sunxi_g2d_mem_reserve=0 sunxi_ve_mem_reserve=0 disp.screen0_output_mode=EDID:1280x720p50 hdmi.audio=EDID:0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait
  61. <6>PID hash table entries: 4096 (order: 2, 16384 bytes)
  62. <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  63. <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  64. <6>allocated 2097152 bytes of page_cgroup
  65. <6>please try 'cgroup_disable=memory' option if you don't want memory cgroups
  66. <6>Memory: 1024MB = 1024MB total
  67. <5>Memory: 993472k/993472k available, 55104k reserved, 270336K highmem
  68. <5>Virtual kernel memory layout:
  69.     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  70.     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  71.     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
  72.     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
  73.     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
  74.     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
  75.       .text : 0xc0008000 - 0xc0860818   (8547 kB)
  76.       .init : 0xc0861000 - 0xc089adc0   ( 232 kB)
  77.       .data : 0xc089c000 - 0xc09105f0   ( 466 kB)
  78.        .bss : 0xc0910614 - 0xc0ae02d8   (1856 kB)
  79. <6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  80. <6>Preemptible hierarchical RCU implementation.
  81. <6>     RCU dyntick-idle grace-period acceleration is enabled.
  82. <6>     Additional per-CPU info printed with stalls.
  83. <6>NR_IRQS:192
  84. <6>Architected local timer running at 24.00MHz.
  85. <6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
  86. <2>start_kernel(): bug: interrupts were enabled early
  87. <6>Console: colour dummy device 80x30
  88. <6>console [tty0] enabled
  89. <6>Calibrating delay loop... <c>1908.73 BogoMIPS (lpj=9543680)
  90. <6>pid_max: default: 32768 minimum: 301
  91. <6>Mount-cache hash table entries: 512
  92. <6>Initializing cgroup subsys cpuacct
  93. <6>Initializing cgroup subsys memory
  94. <6>Initializing cgroup subsys devices
  95. <6>Initializing cgroup subsys freezer
  96. <6>Initializing cgroup subsys blkio
  97. <6>Initializing cgroup subsys perf_event
  98. <6>CPU: Testing write buffer coherency: ok
  99. <6>CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  100. <6>hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
  101. <6>Setting up static identity map for 0x405d38e8 - 0x405d3940
  102. CPU1: Booted secondary processor
  103. <6>CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  104. <6>Brought up 2 CPUs
  105. <6>SMP: Total of 2 processors activated (3824.02 BogoMIPS).
  106. <6>devtmpfs: initialized
  107. <6>dummy:
  108. <6>NET: Registered protocol family 16
  109. <6>DMA: preallocated 256 KiB pool for atomic coherent allocations
  110. <6>hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
  111. <6>hw-breakpoint: maximum watchpoint size is 8 bytes.
  112. <6>[ccu-inf] aw clock manager init
  113. <6>[ccu-inf] aw_ccu_init
  114. <6>[ccu-inf] script config pll3 to 297MHz
  115. <6>[ccu-inf] script config pll4 to 300MHz
  116. <6>[ccu-inf] script config pll6 to 600MHz
  117. <6>[ccu-inf] script config pll7 to 297MHz
  118. <6>[ccu-inf] script config pll8 to 336MHz
  119. <6>Init eGon pin module V2.0
  120. <6>bio: create slab <bio-0> at 0
  121. <6>sunxi_gpio driver init ver 1.3
  122. <6>gpiochip_add: registered GPIOs 1 to 88 on device: A1X_GPIO
  123. <5>SCSI subsystem initialized
  124. <7>libata version 3.00 loaded.
  125. <6>usbcore: registered new interface driver usbfs
  126. <6>usbcore: registered new interface driver hub
  127. <6>usbcore: registered new device driver usb
  128. <6>Linux media interface: v0.10
  129. <6>Linux video capture interface: v2.00
  130. <6>Advanced Linux Sound Architecture Driver Version 1.0.25.
  131. <6>Switching to clocksource arch_sys_counter
  132. <5>FS-Cache: Loaded
  133. <6>CacheFiles: Loaded
  134. <6>cfg80211: Calling CRDA to update world regulatory domain
  135. <6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
  136. <6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
  137. <6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  138. <6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  139. <6>usb usb1: Product: sw_hcd host driver
  140. <6>usb usb1: Manufacturer: Linux 3.4.90+ sw_hcd-hcd
  141. <6>usb usb1: SerialNumber: sw_hcd_host0
  142. <6>hub 1-0:1.0: USB hub found
  143. <6>hub 1-0:1.0: 1 port detected

  144. U-Boot SPL 2014.04-10694-g2ae8b32 (Sep 03 2014 - 20:53:14)
  145. Board: Bananapi
  146. DRAM: 1024 MiB
  147. CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
  148. spl: not an uImage at 1600


  149. U-Boot 2014.04-10694-g2ae8b32 (Sep 03 2014 - 20:53:14) Allwinner Technology

  150. CPU:   Allwinner A20 (SUN7I)
  151. Board: Bananapi
  152. I2C:   ready
  153. DRAM:  1 GiB
  154. MMC:   SUNXI SD/MMC: 0
  155. *** Warning - bad CRC, using default environment

  156. In:    serial
  157. Out:   serial
  158. Err:   serial
  159. Net:   dwmac.1c50000
  160. Hit any key to stop autoboot:  0
  161. sun7i#
Copy the Code

Use "DC in" for power supply!!! Not the USB OTG.

Then it will work fine.

Cubytus  
I am using the DC input, yet it kernel crashes. Green LED is flashing quickly on my unit.

Any idea?

vario  
Hello , I had the same problem, it is indeed a concern for electric power , I changed my original usb cable with a cable samsung micro usb and everything is fine . I can even plug in a hard drive on sata port which was not the case before . Sorry for english ( google translation ).

paul george shoes
nmd
adidas outlet
air force 1
Kanye West shoes
nba jerseys
supreme hoodie
nike air max
adidas tubular shadow
jordan retro
longchamp
pandora charms
moncler jackets
golden goose
kate spade handbags
michael kors outlet online
red bottom shoes
michael kors outlet
nike mercurial
hermes birkin
longchamps
nike air max
golden goose outlet
air max 2017
100% real jordans for cheap
nike foamposite
longchamp outlet
air jordan
ultra boost
curry 4
nike huarache
adidas superstar
lebron james shoes
yeezy shoes
ysl handbags
air jordan shoes
kobe sneakers
jordan 4
nike sneakers
nike cortez men
stephen curry shoes
christian louboutin shoes
longchamp
nmd
lebron 13 shoes
michael kors outlet online
nike huarache
nike air huarache
yeezy shoes
off white clothing
lacoste outlet
fitflops
michael kors handbags
ferragamo belts
cartier bracelet
kate spade outlet
christian louboutin
led shoes
air max 90
longchamp outlet
adidas outlet online
adidas ultra
basketball shoes
adidas superstar shoes
adidas ultra boost
van cleef
jordan shoes
longchamp handbags
kobe basketball shoes
golden goose sneakers
nike polo
yeezy
real jordans for sale cheap
ferragamo belt
adidas nmd runner
cheap jordans
fitflops sale clearance
adidas nmd r1
yeezy boost 350
yeezy
kevin durant shoes
adidas superstar shoes
kobe basketball shoes
michael kors outlet
goyard handbags
tory burch shoes
nike air force 1
hermes belt
nike polo shirts
jordan 13
vapormax
nike roshe
james harden shoes
dior sunglasses
michael kors handbags
nike air huarache
100% real jordans for cheap
nike flyknit
michael kors outlet online
golden goose

You have to log in before you can reply Login | Sign Up

Points Rules